三级2017在线观看免费_婷婷色五丁香_亚洲天堂视频一区_国产无遮挡又黄又爽奶头_亚洲无码在线免费视频_舌吻哼哼唧唧原声不带歌_一级做a爰片毛片潮喷中文字幕无码精品_2020国产精品国产精品_脫了動漫美女內褲猛烈進入gif_人妻中文字字幕在线乱码

MU-PSTX02
控制空間內溫度的理想方法是以所需的量來替換損失的熱量或置換獲得的熱量。使用基本的兩位控制，這樣的操作是不可能的，因為加熱或冷卻系統要么完全打開，要么完全關閉，并且在任何特定時刻的輸送量要么太多，要么太少。然而，定時雙位置控制可以預測需求，并按百分比按時提供測量的加熱或冷卻量，以減少控制點波動。定時由電子控制中的熱預測器和電子和數字控制中的計時器完成。在定時雙位置控制中，控制器和終控制元件之間的基本交互作用與基本雙位置控制相同。然而，控制器對受控變量平均值的逐漸變化而不是周期性波動作出響應。由于熱預測或時間比例特性導致機械設備的循環速度更快，因此可以減少或消除過沖和欠沖。結果是比基本雙位置控制更接近變量控制（圖23）。圖23：。比較基本兩位和定時兩位控制。熱預測在機電控制中，可通過在雙金屬傳感元件上添加熱預測器來實現定時雙位置控制。在加熱系統中，連接熱預測器，使其在雙金屬元件需要加熱時通電。溫度下降時，傳感元件會啟動加熱系統和熱量預測器。熱預測器提前將雙金屬元件加熱到其關閉點，并使加熱系統和熱預測器斷電。隨著環境溫度的下降，雙金屬元件加熱到關閉點所需的時間增加，冷卻時間減少。因此，熱預測器根據環境溫度自動改變開啟時間與關閉時間的比率。由于熱量僅供應給傳感器，因此隨著熱量需求的增加，熱量預測功能會降低控制點。降低的控制點稱為“下垂”，在設計條件下保持較低的溫度，下面將對其進行更深入的討論。在恒溫器關閉期間通電加熱器可實現對恒溫器冷卻的預期操作。在任何一種情況下，接通時間百分比都與系統負載成比例變化。

The ideal method of controlling the temperature in a space is to replace lost heat or displace gained heat in exactly the amount needed. With basic two-position control, such exact operation is impossible because the heating or cooling system is either full on or full off and the delivery at any specific instant is either too much or too little. Timed two-position control, however, anticipates requirements and delivers measured quantities of heating or cooling on a percentage on-time basis to reduce control point fluctuations. The timing is accomplished by a heat anticipator in electric controls and by a timer in electronic and digital controls. In timed two-position control, the basic interaction between the controller and the final control element is the same as for basic two-position control. However, the controller responds to gradual changes in the average value of the controlled variable rather than to cyclical fluctuations. Overshoot and undershoot are reduced or eliminated because the heat anticipation or time proportioning feature results in a faster cycling rate of the mechanical equipment. The result is closer control of the variable than is possible in basic twoposition control (Fig. 23). Fig. 23. Comparison of Basic Two-Position and Timed Two-Position Control. HEAT ANTICIPATION In electromechanical control, timed two-position control can be achieved by adding a heat anticipator to a bimetal sensing element. In a heating system, the heat anticipator is connected so that it energizes whenever the bimetal element calls for heat. On a drop in temperature, the sensing element acts to turn on both the heating system and the heat anticipator. The heat anticipator heats the bimetal element to its off point early and deenergizes the heating system and the heat anticipator. As the ambient temperature falls, the time required for the bimetal element to heat to the off point increases, and the cooling time decreases. Thus, the heat anticipator automatically changes the ratio of on time to off time as a function of ambient temperature. Because the heat is supplied to the sensor only, the heat anticipation feature lowers the control point as the heat requirement increases. The lowered control point, called “droop”, maintains a lower temperature at design conditions and is discussed more thoroughly in the following paragraphs. Energizing the heater during thermostat off periods accomplishes anticipating action in cooling thermostats. In either case, the percentage on-time varies in proportion to the system load.